Hi,
I have been flying the VCol Jetstream 32, but though FDC loads just fine with my profile, for some reason I can't get any flap calls from pilot/co-pilot: these only come if I set flaps myself. I want the pilot and co-pilot to call/confirm flaps as the speed reaches the value in the performance file, but for me to do this myself when the call comes. This is what happens with 99% of my aircraft, and I cannot see why it doesn't with the J32.
The flap/speed settings are correct I think according to the aircraft.cfg file (and in the .uco file) - I should get a first 'flaps 10' call when my speed drops below c.160kts, but I can go right to stall with no calls.
cfg:
flaps-position.0 = 0.000,0.000
flaps-position.1 = 10.000,0.000
flaps-position.2 = 20.000,0.000
flaps-position.3 = 30.000,0.000
flaps-position.4 = 40.000,0.000
pro:
[Captain] CTFlapCalls=1
[CoPilot] FlapCalls=1
[Flaps]
Preset=51
FP1=0
FP2=0
FP3=0
FP4=0
FP5=0
FP10=1
FP15=0
FP20=1
FP25=0
FP30=1
FP35=0
FP40=1
[VCP-X]
HDG=0
ALT=5000
VSI=1000
Bar1=1
Bar2=1
EKey=1
VCPX=1
RevON=1
RevOFF=60
Arm=0
Deploy=0
DefaultVSI=1
AutobrakeON=0
AutobrakeSetting=3
AutobrakeOFF=0
MAPActions=1
DisengageAP=0
DisengageVIS=0
MAPActionsAPOnly=0
ApOnAltTrigger=0
HdgOnAltTrigger=0
AltOnAltTrigger=0
SpdOnSpdTrigger=0
RTO2ON=2
MaxSpd10K=0
CallMillibars=0
MaxTaxi=24
AutobrakeSettingLD767=1
uco:
#Flaps:000001010101
#Takeoff Data
#Data Format: Weight V1 VR V2 Followed by each flaps setting for this aircraft
#--------------------------------------------------------------------------------------------------
049 112 112 115 160 150 140 130 000
048 111 111 114 158 148 138 128 000
047 109 109 113 156 146 136 126 000
046 108 108 111 154 144 135 125 000
042 105 105 110 152 142 130 120 000
035 104 104 110 150 140 128 118 000
000 103 103 109 148 138 126 116 000
#EOD
#Landing Data
#Data Format: Weight followed by each flap setting for this aircraft
#--------------------------------------------------------------------------------------------------
049 160 150 140 130
048 158 148 138 128
047 156 146 136 126
046 154 144 135 125
042 152 142 130 120
035 150 140 128 118
#EOD
No take-off flap calls either. I tried the UI/Select Aircraft and making sure 'Procedure Variation' is #2...
I could upload my files, but maybe that's enough info? I do most of my editing through the files themselves, .uco .pro etc, which I find much easier. What settings should I be looking for over and above the ones I have mentioned to get flap calls? Or, I could check in the UI, if you'd be so kind as to give me a step-by-step.. I have compared files and the UI window with those of a/c which work (most of them, as I say) - but can't see any differences that would account for this. So after an hour's frustration, I am posting here. Thanks.
Hope everyone has a great Christmas...
Martin