OnCourse Software http://www.ocs-support.co.uk/forums/ |
|
No flap calls? http://www.ocs-support.co.uk/forums/viewtopic.php?t=2378 |
Page 1 of 1 |
Author: | martinlest [ Sat Dec 24, 2016 5:48 pm ] |
Post subject: | No flap calls? |
Hi, I have been flying the VCol Jetstream 32, but though FDC loads just fine with my profile, for some reason I can't get any flap calls from pilot/co-pilot: these only come if I set flaps myself. I want the pilot and co-pilot to call/confirm flaps as the speed reaches the value in the performance file, but for me to do this myself when the call comes. This is what happens with 99% of my aircraft, and I cannot see why it doesn't with the J32. The flap/speed settings are correct I think according to the aircraft.cfg file (and in the .uco file) - I should get a first 'flaps 10' call when my speed drops below c.160kts, but I can go right to stall with no calls. cfg: flaps-position.0 = 0.000,0.000 flaps-position.1 = 10.000,0.000 flaps-position.2 = 20.000,0.000 flaps-position.3 = 30.000,0.000 flaps-position.4 = 40.000,0.000 pro: [Captain] CTFlapCalls=1 [CoPilot] FlapCalls=1 [Flaps] Preset=51 FP1=0 FP2=0 FP3=0 FP4=0 FP5=0 FP10=1 FP15=0 FP20=1 FP25=0 FP30=1 FP35=0 FP40=1 [VCP-X] HDG=0 ALT=5000 VSI=1000 Bar1=1 Bar2=1 EKey=1 VCPX=1 RevON=1 RevOFF=60 Arm=0 Deploy=0 DefaultVSI=1 AutobrakeON=0 AutobrakeSetting=3 AutobrakeOFF=0 MAPActions=1 DisengageAP=0 DisengageVIS=0 MAPActionsAPOnly=0 ApOnAltTrigger=0 HdgOnAltTrigger=0 AltOnAltTrigger=0 SpdOnSpdTrigger=0 RTO2ON=2 MaxSpd10K=0 CallMillibars=0 MaxTaxi=24 AutobrakeSettingLD767=1 uco: #Flaps:000001010101 #Takeoff Data #Data Format: Weight V1 VR V2 Followed by each flaps setting for this aircraft #-------------------------------------------------------------------------------------------------- 049 112 112 115 160 150 140 130 000 048 111 111 114 158 148 138 128 000 047 109 109 113 156 146 136 126 000 046 108 108 111 154 144 135 125 000 042 105 105 110 152 142 130 120 000 035 104 104 110 150 140 128 118 000 000 103 103 109 148 138 126 116 000 #EOD #Landing Data #Data Format: Weight followed by each flap setting for this aircraft #-------------------------------------------------------------------------------------------------- 049 160 150 140 130 048 158 148 138 128 047 156 146 136 126 046 154 144 135 125 042 152 142 130 120 035 150 140 128 118 #EOD No take-off flap calls either. I tried the UI/Select Aircraft and making sure 'Procedure Variation' is #2... I could upload my files, but maybe that's enough info? I do most of my editing through the files themselves, .uco .pro etc, which I find much easier. What settings should I be looking for over and above the ones I have mentioned to get flap calls? Or, I could check in the UI, if you'd be so kind as to give me a step-by-step.. I have compared files and the UI window with those of a/c which work (most of them, as I say) - but can't see any differences that would account for this. So after an hour's frustration, I am posting here. Thanks. Hope everyone has a great Christmas... Martin |
Author: | martinlest [ Sat Dec 24, 2016 8:46 pm ] |
Post subject: | Re: No flap calls? |
... I think I spotted something! Will post back after testing it out. |
Author: | martinlest [ Sat Dec 24, 2016 10:55 pm ] |
Post subject: | Re: No flap calls? |
OK, flap callouts are working now. FYI: The takeoff section needed another column (how did I not see that?), but that didn't effect the flap calls when landing I would think (and it didn't cause FDC to crash, I suppose, because of the zeros?). (I was wrong - I was getting a 'flaps up' call after take off). In case it's of any interest:
Martin |
Author: | Dave Leesley [ Tue Dec 27, 2016 11:00 am ] |
Post subject: | Re: No flap calls? |
Any empty columns should have a zero and after last flaps call, I tend to fill remaining columns with zero's so I get flaps up call and make all speeds about 5-8kts difference ie: flaps 1=123 flaps 2=128 flaps 3=135 or something along those lines(depending on what my source of information tells me)...try not to have callouts that close. For landing... a zero should be in last column it can't be left blank as FDC will tell you or any columns...as you have found out. At least you have it working now so you wont make the same mistake twice!.. |
Author: | martinlest [ Tue Dec 27, 2016 12:00 pm ] |
Post subject: | Re: No flap calls? |
Hi Dave. You mean columns or rows? It seems to me that it was adding the last row, starting 000, to the Landing Data that solved the problem. There's no 000 column there (though I have one in the Take Off section). Martin |
Author: | Dave Leesley [ Tue Dec 27, 2016 2:16 pm ] |
Post subject: | Re: No flap calls? |
Sorry I was working down not across..but I could have meant both |
Author: | martinlest [ Tue Dec 27, 2016 3:33 pm ] |
Post subject: | Re: No flap calls? |
As you see, I added the extra row in the landing section (after which, flap calls 'came online'). I may try removing it again, to see if that stops them working, to be sure it's that change that made the difference. I had assumed it to be the change from 3/1400 to 5/1500 (that'd make more sense?), but... |
Page 1 of 1 | All times are UTC+01:00 |
Powered by phpBB® Forum Software © phpBB Limited |