OnCourse Software
http://www.ocs-support.co.uk/forums/

File selected is NOT a valid PF3+FPP file !
http://www.ocs-support.co.uk/forums/viewtopic.php?t=1927		 Page 1 of 1
Author:  drumsart [ Fri Mar 11, 2016 11:26 pm ]
Post subject:  File selected is NOT a valid PF3+FPP file !
This is the received message when I selected a FP from NSTU to NTAA. This FP is accepted by Fsx and Aerosoft Airbus 321.

Thanks in advance

Regards,

Richard Portier
Author:  vololiberista [ Sat Mar 12, 2016 9:57 am ]
Post subject:  Re: File selected is NOT a valid PF3+FPP file !
drumsart wrote:
This is the received message when I selected a FP from NSTU to NTAA. This FP is accepted by Fsx and Aerosoft Airbus 321.

Thanks in advance

Regards,

Richard Portier
It doesn't work recreated in FS9 either. So it could be a LAT/LONG problem perhaps.
Author:  Dave March [ Sat Mar 12, 2016 10:58 am ]
Post subject:  Re: File selected is NOT a valid PF3+FPP file !
There are no control centres for that area at all, not for any part of the flight plan! I'll sort something out and hopefully get it into the next release which won't now be till late tomorrow (Sunday GMT) ;)
Author:  drumsart [ Sat Mar 12, 2016 2:30 pm ]
Post subject:  Re: File selected is NOT a valid PF3+FPP file !
dmarch wrote:
There are no control centres for that area at all, not for any part of the flight plan! I'll sort something out and hopefully get it into the next release which won't now be till late tomorrow (Sunday GMT) ;)
Thank you Dave for following your product and support.

Regards,

Richard Portier
Author:  vololiberista [ Sat Mar 12, 2016 3:28 pm ]
Post subject:  Re: File selected is NOT a valid PF3+FPP file !
drumsart wrote:
dmarch wrote:
There are no control centres for that area at all, not for any part of the flight plan! I'll sort something out and hopefully get it into the next release which won't now be till late tomorrow (Sunday GMT) ;)
Thank you Dave for following your product and support.

Regards,

Richard Portier
Next time you try that flight make sure you've got full survival equipment on board. Plus emergency radios!
Author:  drumsart [ Sat Mar 12, 2016 6:02 pm ]
Post subject:  Re: File selected is NOT a valid PF3+FPP file !
vololiberista wrote:
drumsart wrote:
dmarch wrote:
There are no control centres for that area at all, not for any part of the flight plan! I'll sort something out and hopefully get it into the next release which won't now be till late tomorrow (Sunday GMT) ;)
Thank you Dave for following your product and support.

Regards,

Richard Portier
Next time you try that flight make sure you've got full survival equipment on board. Plus emergency radios!
This is the reason why I use ATC softwares and especially PF3 :mrgreen:

Regards,

Richard Portier
Author:  vololiberista [ Sat Mar 12, 2016 7:04 pm ]
Post subject:  Re: File selected is NOT a valid PF3+FPP file !
drumsart wrote:
This is the reason why I use ATC softwares and especially PF3 :mrgreen:

Regards,

Richard Portier
Technically speaking you wouldn't get ATC coverage in that part of the Pacific. and Dave is correct there are no control Zones there either. A Satellite phone is your best bet!
Author:  Dave March [ Sun Mar 13, 2016 11:31 am ]
Post subject:  Re: File selected is NOT a valid PF3+FPP file !
This problem has now been addressed and will be in the next release (later today).

The issue was caused by the departure, destination and all enroute waypoints falling outside any of the PF3 ATC control zones. :o
Page 1 of 1 All times are UTC+01:00
Powered by phpBB® Forum Software © phpBB Limited