OnCourse Software http://www.ocs-support.co.uk/forums/ |
|
Preferential Runways http://www.ocs-support.co.uk/forums/viewtopic.php?t=2508 |
Page 2 of 3 |
Author: | Alpha117 [ Mon Apr 10, 2017 12:14 pm ] |
Post subject: | Re: Preferential Runways |
I've set this up. Is this correct or do I need to add/change anything else, or am I good to go? Perhaps I could setup a hold at SRN (280knt/FL70). Would I get this or is there a % chance? ![]() |
Author: | vololiberista [ Mon Apr 10, 2017 12:44 pm ] |
Post subject: | Re: Preferential Runways |
You can certainly set-up SRN as a hold and in addition in the misc options of options 1 select the probability percentage. Set to high if it is a busy airport which LIML is. However PF3 will tell you to reduce your speed to 220kts for the holding pattern. |
Author: | Alpha117 [ Mon Apr 10, 2017 12:52 pm ] |
Post subject: | Re: Preferential Runways |
Thanks Right then, I'm off to LIML, let you know how it goes ![]() |
Author: | Alpha117 [ Mon Apr 10, 2017 2:14 pm ] |
Post subject: | Re: Preferential Runways |
On climb to cruise, no issues so far. Was given initial level of 4000ft, didn't hear any climb altitude after reaching 4000ft. OK, just arrived at 1st route WP at FL300 and been told to descend to 4000ft... ![]() Not sure what is happening, but I'm on route and should be a cruise not descending to 4000ft. I've missed something I think. OK, ill abort this flight and attach log, so you can see what I have missed thanks |
Author: | ThomasAH [ Mon Apr 10, 2017 2:22 pm ] |
Post subject: | Re: Preferential Runways |
You never waited to be cleared for more than 4000 feet, ATC was just a bit slow to remind you of this fact. You can decrease the altitude nag interval, I have set mine to 30 seconds, I think the default is 120 seconds. You can usually get out of such situations by requesting a new altitude, e.g. press and hold the "L" key, shortly press "2" (for 2000 lower), release "L". Then either immediately request "higher due to turbulences" (which adds 2000 feet to the last cleared altitude) or first descend and then hold H, press 2, release H for 2000 higher. |
Author: | Alpha117 [ Mon Apr 10, 2017 2:27 pm ] |
Post subject: | Re: Preferential Runways |
Thanks Thomas Will change it to 30seconds also |
Author: | Alpha117 [ Mon Apr 10, 2017 4:09 pm ] |
Post subject: | Re: Preferential Runways |
Off again, this time from 25C, departure spot on ![]() 'Request ACARS ATIS for your destination', can't get anything when pressing '2', again I must have missed something. On route climb, very good ![]() Update reached TOD told to descent to FL300, then to FL260, but ATC has not given 'Expect arrival xyz', so I do not know what my arrival should be or even the arrival runway ![]() |
Author: | ThomasAH [ Mon Apr 10, 2017 4:31 pm ] |
Post subject: | Re: Preferential Runways |
Good to hear that most things went well. Regarding the ACARS ATIS: This is displayed in the flight sim's kneeboard, which P3D does not have. |
Author: | Alpha117 [ Mon Apr 10, 2017 4:37 pm ] |
Post subject: | Re: Preferential Runways |
Aaarh OK, with the ATIS. OK just been haned over to Approach, again all I got was rgr OK. Surely On the initial approach contact the controller should give the approach and active runway? Also the last center control, before handing over to approach should give the 'Expect xyz'. yes, we all know that in the US that can be 100's miles from destination ![]() So, now with approach and on the descent and still not knowing what teh approach or runway is ![]() What am I missing ![]() |
Author: | Alpha117 [ Mon Apr 10, 2017 4:45 pm ] |
Post subject: | Re: Preferential Runways |
Just been given by approach 'Continue on the XYZ approach' ![]() I've plumbed in an approach into the FMC, hoping it's the correct one. Let you know when I'm down Surely I have missed something on the approach section of this flight ![]() Update: now ATC is saying 'check position, you show 4 miles off the airway'........ Update1: Just received cleared runway ILS36 Update3: Was 'cleared' runway 36 and now ATC says I have a runway change to runway 18, sorry that cannot happen once ATC has given you 'cleared. contact tower when established' If there is going to be a runway change then ATC has to make that change BEFORE given the 'cleared...etc etc' command. So, what did I miss or what do I need to change Flight aborted |
Page 2 of 3 | All times are UTC+01:00 |
Powered by phpBB® Forum Software © phpBB Limited |